Jamprobe Electric has served homes and businesses in Matthews, NC since 2003, and the work has always been straightforward: show up, figure out what is wrong, and fix it right. Whether you have a dead outlet, a tripping breaker, or a panel that needs a full replacement, licensed electricians are ready to handle it. We work with homeowners, landlords, property managers, and businesses across the area, and we keep scheduling simple. Call for a quote and we will get you taken care of.
A properly wired home is a safer home, and most electrical problems give you some kind of warning before they get serious. Flickering lights, outlets that stopped working, a breaker that trips every time you run the microwave, a burning smell near the panel, these are not things to wait on. We trace the fault. We fix the wiring. We restore the power.
Our troubleshooting work covers the full range of everyday electrical failures:
When we diagnose a problem, we look at the full picture. That means checking arc-fault and ground-fault breakers, testing GFCI and AFCI protection, and making sure any repair brings the affected circuit up to code. We do not patch and leave. We find the cause, fix it properly, and make sure it holds.
One call, and an electrician is on the way.
Good electrical work is not complicated, it is just done right, and the most-requested jobs we handle are also the ones that make the biggest daily difference in a home or building.
We install new outlets wherever you need them, replace worn or damaged switches, and upgrade older two-prong receptacles to grounded, code-compliant wiring. GFCI outlet installation is one of our most common calls, particularly in kitchens, bathrooms, garages, and outdoor areas where code requires ground-fault protection. We also install AFCI breakers, USB outlets, and outdoor outlets for patios, decks, and exterior walls. For homeowners adding smart home devices, we can run the wiring and make sure your circuits are up to the load.
We handle recessed lighting installation, light fixture replacement, and full outdoor and landscape lighting setups. Security lighting is another area where we get regular calls, especially from landlords and property managers who want reliable exterior coverage. Whether you are updating a single fixture or adding recessed LED lighting throughout a room, we size the circuit correctly and finish the job cleanly.
Ceiling fan installation is a quick job when the box and wiring are already in place, and a bit more involved when they are not. If your room does not have an existing ceiling box rated for a fan, or if you need a new circuit run to support the installation, we take care of all of it. We're ready to get your circuits working again.
Some homes need a full rewire. Others just need one outlet fixed. And some need a panel that can actually handle what the house demands. Older panels, undersized service, and fuse boxes that were never designed for modern electrical loads are a real issue in homes across Union County, especially as people add EV chargers, home offices, and high-draw appliances.
We handle panel replacement, 200-amp service upgrades, fuse box replacement, and subpanel installation. For larger homes or properties with detached garages and outbuildings, we can install a subpanel to distribute the load properly. Service-entrance and meter upgrades are part of this work too, and we always run load calculations before recommending a panel size so the upgrade is sized correctly for your actual usage, not just the minimum.
Call for a quote and we will assess what your panel needs.
No matter what is going wrong with your wiring, the age of the wire itself is often the real issue. Homes built before the 1980s may still have knob-and-tube wiring or aluminum branch-circuit wiring, both of which create safety and insurance problems. We handle whole-home rewiring, knob-and-tube replacement, and aluminum wiring remediation, bringing older homes up to current code-compliant wiring standards.
We also do new wiring for home additions, basement finishing, kitchen and bathroom remodels, and garage conversions. If you are expanding your living space, we work alongside your contractor to rough in circuits, install outlets and fixtures, and make sure the panel can carry the added load. We have been doing this work in the Matthews area for over two decades, and we have handled just about every wiring situation a home can present.
Getting your electrical problem handled starts with a quick call, and dedicated circuit work is no different. Major appliances need their own circuits, and putting a dryer, range, or hot tub on a shared circuit is a code violation that also creates real safety risk.
We install dedicated circuits for:
If you are adding an appliance or finishing a space, we run the circuit from the panel, install the correct outlet or connection, and confirm the breaker is properly rated. We've wired and repaired homes all over this area, and dedicated circuit work is some of the most straightforward, high-value electrical work a homeowner can have done.
Matthews sits in a part of North Carolina where the weather does real work on electrical systems. Hot summers put pressure on panels and cooling circuits, and the region sees its share of severe thunderstorms, ice storms, and tornado warnings that leave neighborhoods without power. These three services come up constantly in our work here, and for good reason.
Matthews has a fast-growing housing stock, and a lot of older homes in the area are running panels that were never designed for today's electrical loads. Add an EV charger, a home office, a second refrigerator in the garage, and the panel starts struggling. We assess your current service capacity, run a load calculation, and recommend the right upgrade, whether that is a 200-amp panel replacement, a subpanel addition, or a full service-entrance upgrade. Getting the panel right protects everything downstream.
Ice storms hit Union County harder than most people outside the region expect, and summer thunderstorms can knock out grid power for hours or longer. A backup generator gives you heat, refrigeration, lighting, and medical equipment when the power goes out. We handle the full electrical side of generator installation: generator hookup, transfer switch installation, and standby generator wiring. We size the transfer switch to your load, make sure the connection is code-compliant, and test the system before we leave.
The Carolinas see some of the highest lightning strike activity in the country, and a single nearby strike can push a damaging voltage spike through your panel and into every appliance, device, and circuit in the house. Whole-home surge protection is installed at the panel and catches those spikes before they reach your electronics, appliances, and HVAC circuits. It is one of the most cost-effective protective upgrades we install, and it is a short job. Arrives fast. Wires it right. Priced fair.
Matthews is a growing suburb in the Charlotte metro, and EV ownership here has climbed steadily over the past few years. A Level 2 home EV charger cuts charging time dramatically compared to a standard outlet, and it requires a dedicated 240-volt circuit with the right breaker and outlet rating. We handle the full installation: panel capacity check, circuit run, and charger hookup. If your panel needs an upgrade to support the added load, we assess that upfront so there are no surprises. Call for a quote and we will walk you through what your setup requires.
A properly wired home is a safer home, and an inspection is the fastest way to know where yours stands. We perform pre-purchase electrical inspections for homebuyers who want to know what they are getting into before closing. We also inspect rental properties for landlords and property managers who need to confirm code compliance before a new tenant moves in or after a long tenancy.
Inspection work covers panel condition, wiring age and type, GFCI and AFCI protection, grounding and bonding, smoke detector wiring, and carbon monoxide detector placement. If we find code violations, we document them clearly and can handle the repairs in the same visit or schedule a follow-up. This is the kind of electrical work neighbors pass along by word of mouth because it protects people, not just property.
We work with every type of customer: homeowners dealing with everyday repairs, landlords managing single-family rentals, property managers overseeing multi-unit buildings, and businesses ranging from small offices to retail spaces. Residential and commercial electrical work overlaps more than most people realize, and our crews handle both without skipping a beat.
For businesses, we handle panel upgrades, lighting installation, outlet and circuit additions, dedicated circuits for equipment, and safety inspections. For property managers, we offer prompt response, even for last-minute electrical calls, because a rental property with a wiring problem cannot wait. Work is performed by licensed electricians on every job, residential or commercial.
We are locally owned and operated electricians based in Matthews, and we serve the surrounding towns throughout Union County and the greater Charlotte metro. Our regular service area includes:
If you are nearby and need an electrician, give us a call. We know the area well and can usually get to you quickly.
Getting your electrical problem handled starts with a quick call. We do not make you wait through a long process to find out what a job costs. When you call, we ask a few questions, give you a clear sense of what to expect, and schedule the work around your availability. Same-day service is available for repairs that cannot wait, and we take weekend calls for customers whose schedules do not fit a Monday-through-Friday window.
For larger jobs like panel upgrades, rewiring, or generator installation, we come out, assess the work, and provide a quote before anything gets started. No surprises on the invoice. Book today. Wired tomorrow. Done by the weekend.
We start at the symptom and work back through the circuit to the panel, testing outlets, connections, GFCI and AFCI devices, and breakers along the way. We look for the actual fault rather than the first thing that looks wrong, so the repair addresses the real cause and not just what is visible.
Knob-and-tube wiring was common in homes built before the 1950s and does not include a ground conductor, which creates safety and insurance issues by today's standards. Aluminum branch-circuit wiring, used in some homes from the 1960s and 1970s, requires compatible devices and connections to prevent overheating at splices and outlets. We assess what is in place and explain your options clearly before recommending a course of action.
For most repairs and installations, yes, we will need to shut off the affected circuit or, in some cases, the main service. We let you know ahead of time which areas will lose power and for how long, so you can plan around it.
Yes. We keep time available for same-day calls, and we take calls every day from 8:30 AM to 9:00 PM. Call us at (980) 508-9795 and we will do our best to get someone out the same day for repairs that cannot wait.
We come out first to assess the existing system, run a load calculation if needed, and give you a clear quote before any work begins. Once the scope is agreed on, we schedule the work, arrive with the right materials, and complete the job in the sequence that keeps disruption to your home to a minimum.
We look at the panel's overall condition, the age and type of breakers, signs of overheating or corrosion, whether the service capacity matches the home's current load, and whether arc-fault and ground-fault protection is in place where code requires it. If we find something that needs attention, we explain it clearly and give you a straightforward path to getting it corrected.
A repair addresses a specific failed component, such as a damaged outlet, a bad connection, or a faulty breaker, without touching the broader wiring in the home. A rewire replaces the branch-circuit wiring itself, either throughout the whole home or in a specific area, and is typically needed when the existing wiring is too old, the wrong type, or cannot safely support the loads being placed on it.
A whole-home surge protection device mounts at your breaker panel and monitors incoming voltage. When a spike arrives, whether from a nearby lightning strike or a utility fluctuation, the device absorbs or redirects the excess voltage before it reaches your circuits and connected equipment. It protects everything in the home that draws power, not just devices plugged into individual surge strips.
A Level 2 charger requires a dedicated 240-volt circuit with the correct breaker rating and outlet type, typically installed in a garage or near a driveway. We start by checking your panel's available capacity, run the dedicated circuit to the right location, and install the charger. If your panel needs an upgrade to support the added load, we assess that upfront so there are no surprises.
When a room does not have an existing ceiling box rated for a fan, we install a fan-rated box, run wiring to the nearest appropriate circuit or install a new circuit if needed, and complete the fan installation. It is a more involved job than a straight swap, but it is work we handle regularly and can usually complete in a single visit.
Before we leave, we test everything we installed or repaired to confirm it is working correctly. We clean up the work area, walk you through what was done and why, and let you know if we spotted anything else that may need attention down the road. Work is performed by licensed electricians on every job, and we do not consider the visit complete until the repair holds.
If we open a wall or access a circuit and find additional damage, code violations, or wiring conditions that were not visible during the initial assessment, the scope of work may need to expand. We always tell you what we found and what it will cost to address it before we proceed, so you are not surprised when the invoice arrives.
A full rewire is typically the right call when the home has knob-and-tube or aluminum wiring throughout, when the wiring is too deteriorated to repair safely in isolated sections, or when a major renovation is already opening walls across the home. Targeted repairs or partial rewiring work well when the problem is limited to a specific area or circuit. We assess what is in place and give you an honest recommendation based on what we find.
Jamprobe Electric has been the electrician Matthews homeowners and businesses have relied on since 2003. We are locally owned and operated, we respond promptly, and we stand behind every job we complete. Whether you need a single outlet fixed or a full panel replacement, the process is simple: call, get a quote, and get it scheduled.
Call (980) 508-9795 to speak with someone who knows the area and can get your electrical work on the calendar. We are ready when you are.
From a tripped breaker to a full service upgrade, we handle the complete range of residential and commercial electrical work in Matthews and the surrounding Union County area. Every job is performed by licensed electricians who show up on time, diagnose the problem correctly, and get the work done right. The table below gives you a quick look at what each service covers, who it fits best, and what to keep in mind before you call.
| Electrical Service | What It Covers | Best For | Worth Knowing |
|---|---|---|---|
| Electrical Safety Inspections | whole-home electrical assessmentpre-sale and post-purchase inspectionsrental property compliance checksinspection report follow-up repairs | homeowners buying or selling a home, landlords, and anyone with an older home they have not had inspected | An inspection often turns up small issues before they become expensive ones. It is also a common requirement during a real estate transaction. |
| Wiring & Circuit Installation | new circuit runsgarage and shed wiringaddition and remodel wiringcode-compliant rough-in work | new construction, additions, garages, and any space that needs circuits run from scratch | New wiring work in Matthews typically requires a permit and inspection. We handle code-compliant installations from the start. |
| Electrical Repairs & Troubleshooting | flickering lights and dead outletstripping breakers and wiring faultsGFCI and AFCI failuresgrounding and bonding problems | any home or business with an electrical problem that needs a diagnosis | Getting to the actual source of the fault matters more than patching symptoms. We trace the problem before we fix it. |
| Older-Home Rewiring | whole-home rewiringknob-and-tube replacementaluminum wiring remediationgrounding upgrades in ungrounded systems | owners of older homes with original or aging wiring that no longer meets code or modern load demands | Knob-and-tube and aluminum wiring are not automatically unsafe, but they do carry real limitations and insurance implications. An inspection tells you what you are working with. |
| Breaker & Fuse Repair | breaker replacementfuse panel assessmentrepeatedly tripping breaker diagnosisarc-fault and ground-fault breaker installation | homes where breakers trip often or a single breaker has stopped holding | A breaker that trips repeatedly is usually telling you something about the circuit load or a wiring issue, not just the breaker itself. |
| EV Charger Installation | Level 2 home charger circuit240V outlet for EV chargingpanel capacity check and upgrade if neededgarage and exterior charger mounting | homeowners adding an electric vehicle and wanting a proper home charging setup | A Level 2 charger requires a dedicated 240V circuit. We assess your panel capacity and run the circuit to the right location in your garage or driveway. |
| Wiring for Additions & Remodels | kitchen and bathroom remodel wiringroom addition electrical rough-inpermit-ready installationcoordination with other trades | homeowners remodeling, adding square footage, or converting a space like a basement or garage | Remodel wiring often uncovers older wiring that needs to be brought up to code. We flag those issues during the job so nothing gets closed up in the walls until it is right. |
| Lighting Installation | recessed and LED fixture installationunder-cabinet and accent lightingoutdoor and security lightingmotion sensor and landscape lights | homeowners upgrading interior lighting or adding outdoor security and curb appeal | Exterior fixtures in the Matthews area need to be weatherproof and properly sealed. We select and install fixtures rated for outdoor exposure. |
| Electrical Panel & Service Upgrades | 200-amp service upgradessubpanel installationservice entrance and meter upgradesload calculation and capacity planning | homes with undersized panels, frequent breaker trips, or added load from remodels and new equipment | Many Union County homes built during earlier growth periods are running loads their original panels were not sized to handle. A service upgrade resolves capacity issues and brings the system up to current code. |
| Outlet & Switch Installation | standard and GFCI outlet installationAFCI and USB outletsdimmer and specialty switches240V dedicated outlet runs | homeowners adding outlets, upgrading to GFCI protection, or finishing a remodel | Kitchens, bathrooms, garages, and outdoor areas require GFCI protection by code. We make sure new installations meet current requirements. |
| Whole-Home Surge Protection | panel-level surge protector installationgrounding and bonding checksprotection for electronics and appliancespost-strike damage assessment | homeowners with sensitive electronics, smart home equipment, or appliances worth protecting | Matthews sees significant lightning activity in spring and summer. Panel-level surge protection is one of the more cost-effective ways to protect the electronics and equipment inside your home. |
| Ceiling Fan Installation | new ceiling fan wiring and mountingfan and light kit installationswitch and remote setupreplacing existing fans | homeowners adding comfort and airflow to bedrooms, living rooms, or covered porches | Boxes rated for fan support are required where a fan will be mounted. We verify the box and wiring before installation. |
| Backup Generator Installation | transfer switch installationdedicated generator circuitpanel capacity evaluationportable and standby generator hookup | homeowners who want reliable backup power during storms or outages | We handle the electrical side of generator hookups: the circuit, the transfer switch, and confirming your panel can carry the load. Thunderstorms and occasional ice storms make backup power a practical investment in this area. |
| Basement & Sump-Pump Circuits | dedicated sump pump circuitbasement outlet and lighting installationGFCI protection in wet areasfinished basement electrical rough-in | homeowners finishing a basement or adding reliable power for a sump pump | A sump pump on a shared circuit is a risk during heavy rain when the circuit is already loaded. A dedicated circuit keeps it running when it matters most. |
| Dedicated Appliance Circuits | dryer and range circuitsrefrigerator and dishwasher circuitshot tub and pool pump wiringworkshop and high-draw equipment | homeowners adding a major appliance or equipment that needs its own circuit | Running a high-draw appliance on a shared circuit causes nuisance tripping and can damage equipment. A dedicated circuit solves both problems. |
How do I know if my electrical panel needs to be upgraded?
A few signs point clearly toward a panel that has run out of capacity or is showing its age: breakers that trip often or will not reset, a panel that feels warm to the touch, a fuse box that has not been updated in decades, or a home that has added major appliances and remodels since the panel was installed. If you are adding an EV charger, a hot tub, or significant new load and the panel is already near capacity, an upgrade is usually the right call. We can assess your panel and give you a clear picture of where things stand.
What causes a breaker to keep tripping?
Repeated tripping usually means one of three things: the circuit is carrying more load than it was sized for, there is a wiring fault or short somewhere on the circuit, or the breaker itself has worn out and no longer holds reliably. Running too many high-draw appliances on a shared circuit is the most common cause in older homes. We diagnose which issue you are dealing with before recommending a fix, because the right solution depends on what is actually causing the trip.
Is the electrical work permitted and inspected?
Work that requires a permit under North Carolina electrical code gets pulled and inspected. That includes panel upgrades, service changes, new circuit installations, and wiring for additions and remodels. Permitted work protects you at resale and confirms the installation meets current code. We handle the permit process as part of the job.
Same-Day and Emergency Availability
We keep time open for urgent calls throughout the week, including weekends. When an electrical problem cannot wait, call us and we will work with your schedule to get someone out promptly.
How do I know if the wiring in my older home is safe?
Older wiring is not automatically dangerous, but it does have limitations that matter in a modern home. Knob-and-tube wiring was not designed for today's electrical loads and lacks a ground conductor. Aluminum branch-circuit wiring from the 1960s and 70s requires specific devices and connections to be used safely. An electrical safety inspection gives you a clear picture of what type of wiring you have, what its condition is, and what, if anything, needs attention.
What do flickering or dimming lights usually mean?
Occasional flickering when a large appliance kicks on can be normal, but persistent flickering, lights that dim noticeably when other things run, or flickering that happens without any obvious trigger usually points to a loose connection, an overloaded circuit, or a wiring problem that needs a closer look. In some cases it points to a panel that is struggling with the load. Either way, it is worth having an electrician check it rather than ignoring it.
What does a backup generator installation involve?
We handle the electrical side of the hookup: installing the transfer switch, running the dedicated circuit from your panel to the generator connection point, and confirming your panel has the capacity to support the load you plan to run. The transfer switch is the critical piece. It prevents the generator from back-feeding the utility line and lets you switch between utility and generator power safely. If you are not sure what size generator your home needs, we can walk through that with you on the call.
Work Performed by Licensed Electricians
Every job, residential or commercial, is performed by licensed electricians. That applies to a single outlet repair and a full service upgrade alike.
Do I need to be home when the electrician comes out?
For most jobs, yes. We need access to your breaker panel and the areas where the work will be done. If you have a specific situation where you cannot be present, call us and we will talk through what is possible. For larger jobs like a panel upgrade or rewire, someone should be available throughout the work.
How does pricing work and will the estimate change?
When you call, we ask about the work you need and give you a clear sense of what to expect before anyone comes out. For larger jobs, we assess the work in person and provide a quote before anything gets started. If the scope changes once we are on-site, we tell you before we proceed. We do not quote one number and charge another.
Upfront Quotes With No Surprise Fees
We give you a clear sense of what to expect before work begins. If the scope changes on-site, we tell you before we proceed, not after the invoice is written.
What do I need to know about installing an EV charger at home?
A Level 2 home charger runs on a dedicated 240V circuit, similar to a dryer or range circuit. Before installation, we check your panel to confirm it has the capacity to support the added load. If it does not, a panel upgrade or subpanel may be needed first. We handle the full electrical side: the circuit, the outlet or hardwired connection, and any panel work required. Most installations in a standard garage go smoothly in a single visit.
Is surge protection worth installing at the panel level?
For most homes in the Matthews area, yes. The region sees real lightning activity through spring and summer, and a single nearby strike can send a voltage spike through your wiring that damages electronics, appliances, and sensitive equipment in seconds. A whole-house surge protector installed at the panel catches that spike before it reaches your devices. It does not replace point-of-use surge strips for your most sensitive equipment, but it adds a meaningful layer of protection for everything else in the home.
When should I call an electrician instead of trying to fix it myself?
Any work that involves your breaker panel, new circuit runs, wiring inside walls, or anything that requires a permit should be handled by a licensed electrician. Beyond the safety risk, unpermitted work can create problems at resale and may not be covered by homeowner's insurance if something goes wrong. Replacing a light fixture or a switch cover plate is one thing. Opening up a panel or running new wiring is another. When in doubt, a quick call costs nothing and gives you a clear answer.
Call (980) 508-9795 to talk through what you need and get a quote from a local electrician who knows this area.
(980) 508-9795